1. 2.E1/E2 Code

• Cut off power and check the voltage. Let the machine cool before restarting;
• Avoid direct airflow from fans or AC to prevent temp detection issues;
• Clear any obstacles around the machine for proper heating.

2. 3.Ironing Tips

• Please run a quick test as per the manual before the first use;
• Ensure the fabric surface is flat for full contact with the heat plate;
• If any part of the material isn't fully stuck (like heat transfer vinyl or sublimation paper), cover it with clear protective film and Teflon sheet, then press again for 10-15 seconds.

3. 4.Unable to Press Down

1. 2.Ironing Tips

• Please run a quick test as per the manual before first using;
• Ensure the fabric surface is flat for full contact with the heat plate;
• If any part of the material isn't fully stuck (like heat transfer vinyl or sublimation paper), cover it with transparent plastic and Teflon, then press again for 10-15 seconds.

For more concerns and questions, please contact customer service and offer videos operating the above solutions for further assistance.

1. 2.Unable to Power On

• Ensure the voltage value is correct;
• Turn off the machine and unplug the power cord, then re-insert the cord and press the power button to restart the machine;
• Change the power outlet.

1. 1.Cutting/Weeding Tips

• Test a small piece of heat transfer vinyl before the first use (following the manual);
• Check the cutting blade for damage and replace it if needed;
• Cut according to the manual's instructions. If the vinyl didn't get cut through, try increasing the Passes and Force by 1-2 units;
• Using a hook weeder aids in faster and easier cutting.

2. 2.Ironing Tips

• Apply the vinyl to a smooth and flat substrate. For fabric, iron it flat first;
• Place the vinyl design on the substrate with the protective film facing up, cover a Teflon sheet, and iron the vinyl following the steps and parameters in the manual;
• Remove the clear protective film by cold peeling;
• Check vinyl edges after ironing. Cover it with clear protective film and Teflon sheet if not stuck, then iron it again for 10-15s.

3. 3.Washing Tips

• Wait 24 hours after ironing to wash in cold water (20℃-30℃);
• Handwash gently and turn the clothing inside out;
• No dry cleaning;
• Please re-iron the vinyl if it lifts after washing.

1. 2.Cutting/Weeding Tips

• Test a small piece of permanent vinyl before the first use (following the manual);
• Check the cutting blade for damage and replace it if needed;
• Cut according to the manual's instructions. If the vinyl didn't get cut through, try increasing the Passes and Force by 1-2 units;
• Gently weed the permanent vinyl to ensure design integrity;
• Using a hook weeder aids in faster and easier cutting.

2. 3.Transfer Tips

• Scrap the permanent vinyl onto transfer tape with a scraper;
• Pull transfer tape to peel the permanent vinyl from the backing sheet;
• Apply permanent vinyl to the substrate: scrap the vinyl and remove it from the transfer tape gently.

3. 4.Removal Tips

• Just peel off the permanent vinyl from your projects if needed;
• Use adhesive remover for any residue.

1. 1.Heat Transfer Tips

• Test a small piece of sublimation paper before the first use (following the manual);
• Great for: 1. Hard and heat-resistant materials with thermal sublimation coating (like glass, wood, resin, etc.); 2. Polyester and other fabrics with cotton content ≤ 30%;
• Not for: Fabrics with cotton content ＞ 30%.
• Heat transfer results depend on temperature, time, and material. If the color is light, consider increasing the time or temperature, then retest with a small pattern.

1. 1.Heat Transfer Tips

• Test a small piece of heat transfer paper before the first use (following the manual);
• Choose fine-textured materials for improved results;
• If the material isn't fully stuck consider increasing the ironing time and temperature slightly based on the recommended parameters;
• Re-iron any unstuck areas.

1. 1.Transfer Tips

• For better result, press transfer tape firmly on unstuck vinyl and peel the backing sheet off;
• To decrease tape adhesion, apply fine-textured fabric to the transfer tape.

1. 1.Damp Printing Paper

• Ensure correct printer settings;
• Allow ink to dry completely after printing with an inkjet printer;
• Use laminating sheet or water-resistant spray for better results.

1. 1.Cutting Mat Tips

• Select a cutting mat with appropriate adhesion for the material;
• Generally, stickiness weakens after multiple uses;
• Clean the cutting mat with dish soap and a scraper to remove small debris.